Aeros Firmware 5.0.x

[tcaron20]

How was the error code 0 resolved? Same problem for me trying to update 5.0.3. Same result when trying to reload 4.3.1. Wi-Fi and SD card load file but crash while updating.

Thanks!
Tom

[GUY1]

aeros .bin?

[skw]

I did update and seems OK. when using midi song select I get an error message that says:

main-midisongselctbyIdFailed-none-found-
message

the good news is that song does load after that and message goes away (phew!)

[Quad]

Looked for the latest docs on the main website and they are for old versions.

Would be good to have an expanded section on midi setup as that is now much more complicated.

[doclamb0]

Do I need to re install the 5.03 release of the firmware from5.03 beta?

[BrennanSingularSound]

@NYHC

There is a bug with midi cc and Solo track on 5.0.3.

This will be handled soon, thanks for reminding us!

Update 5.0.3 Solo track bug with midi cc

Hello Update to 5.0.3. The result is . There is a bug with the solo track and midi CC it seems that I can not select the Solo track that I want with my Maestro, but need to select the track that I want to play solo, on the Aeros first. This cc commands was always working like a charm with all the previous version.But not with 5.0.3 Video is sending to the support @Brennan take a look please . Thank you and hope you can fix this asap Cheers

@tcaron20

Tried updating to 5.0.3 with Wi-Fi but Error code 0,

Please reach out to support@singularsound.com

@midlo

1, Is there limitation on how long can backing track be? Can it be hour long or are we bound to the 20minutes length limit (mono) or 10 minutes (stereo) fir total track length?

Track limits apply to backing tracks

@midlo

2, I never understood the information about exceeding the 20minutes limit by saving the song. Can you please elaborate? Does it mean, that I can record total length of tracks 20minutes, save, and then record few more tracks to the song?

The Aeros is dynamically loading the audio from the SD card or Internal Memory in real time versus having the song fully loaded on the RAM. This allows us to offload a good chunk of the RAM memory to the SD or Internal memory when saving the song. So you will be able to still record another 19ish minutes after saving the initial track. Note you cannot have multiple max rec time tracks back to back since the time will dynamically decrease with more tracks recorded, even after saving them.

@WillR

First, I (and lots of us) compose a blank template song as a base and build the entire song live. We will then erase all parts and build a new song from that same template song. In previous versions, the Lock state stayed the same. i.e. after we deleted all parts with a long Long press of the top button, the first track would stay Locked if it were previously. In this new version, the top track reverts to Unlocked and you have to slide out the menu to re-lock. Please consider adding this feature again.

Thanks for the feedback we can consider doing this, sure.

@WillR

Please also make the lock happen when you touch the screens green track button as previous versions. This is a quick thing to do on the fly.

We can look into this, currently doing this while playing is more likely than while stopped since while stopped the song dashboard is usually there

@WillR

Secondly, please consider adding an option to NOT view song details when a song is opened. Sometimes less is more.

We considered someone may ask for this… it could be a setting but what would you expect to see when opening a song, just the name?

let me know thanks!

@NYHC

You can lock a track trough the mixer aswell
It’s easy and handy ,without to bend down

We removed this feature as it was clunky and is replaced by the more intuitive slideout method

@Brian108

Hi!
Hopefully this is the right place to post. I updated Aeros to latest firmware. The conversion of the song files on SD and Aeros internal popped up and I hit no. Tried transferring to computer through recommended route, said “corrupted file” and it abandoned backup or transfer.

Please write to support@singularsound.com for assistance

@isaactakeuchi

Fade to Mute is not functioning at all on any of the tracks.

Nice catch! We will look into this

@isaactakeuchi

Loop Decay only reduces the volume on the first track. Subsequent overdubs are deleted and only the original track remains with reduced volume and the last recorded overdub. For example if i record 1 track that plays normal, first overdub reduces the base track to 50% as expected, the next overdub deletes the previous overdub the base layer remains. I was under the impression from the tutorial video that it would reduce the base layer another 50% and the previous overdub 50% and would continue stacking like this. Which would be cool.

Please send a video showing what you mean to support@singularsound.com

@tcaron20

How was the error code 0 resolved? Same problem for me trying to update 5.0.3. Same result when trying to reload 4.3.1. Wi-Fi and SD card load file but crash while updating.

Please write to support@singularsound.com

@skw

did update and seems OK. when using midi song select I get an error message that says:

main-midisongselctbyIdFailed-none-found-
message

the good news is that song does load after that and message goes away (phew!)

Thanks we will look into this!

@Quad

Would be good to have an expanded section on midi setup as that is now much more complicated.

Oh, it’s coming!

@doclamb0

Do I need to re install the 5.03 release of the firmware from5.03 beta?

Nope! If you were on 5.0.3 already you can remain on it no problem

Thanks for all the feedback all!

[tcaron20]

Jay at support sent me the flash file and instructions to re-flash the operating system. Easily done and the 5.0.3 went through via Wi-Fi without a hitch.

Thanks Brennan and SIngular.

[chrisg]

Hi. Just installed 5.0.3. I see an Aeros behavior change that I think is a bug. I would be happy if there is a workaround.

With the previous software version, I had implemented a “Play Aeros Loop Once - with a single press” of my MIDI controller pedal. This was implemented by sending :

1. CC-43 with Value=1 (Start Song)
2. Waiting 100msec. and then sending CC-43 with Value=0 (Stop Song) which would result in the loop stopping when it reach its end and not repeating

With 5.0.3, this sequence of MIDI commands results in the loop starting to play and then stopping immediately. If I send the Stop command even 1.0 sec. after the first command, I still have this problem. If I send the Stop command much later - say 10 sec. then it has the result I want, but my midi controller cannot support such a long wait time.

Can this be fixed - ie, reverted to the behavior pre-5.0 ?

Or, is there a better way for me to send a “Play Loop Once” command to the Aeros ?

[gee_david]

Regarding the small text on the screen, I just posted in the Feature Request some thoughts on making the UI more readable. Example (my crude UI mockup):

Here is the Feature Requewt:

Make Aeros 5.x UI more giggable

Disclaimer: I love the Aeros. The new 5.0 release is a major upgrade for many reasons. Just the existence of Albums makes it finally a giggable tool without the need for a MIDI controller. Great work. As a product manager for a software company, I know how hard big releases like this are. Well done. A lot of people have requested that Singular should “make the text bigger” on the Aeros. My request, though similar on the surface, is more about making the Aeros an easier tool with which to gig. B…

[Quad]

@chrisg

Can this be fixed - ie, reverted to the behavior pre-5.0 ?

Wonder if this is related to your stop settings no longer being set to “end of loop”?

Related, I want a way to play part once and then go back to prior part (or next part). This is for a chorus or bridge and then going back to the A (or B) section. Would be nice if this was a feature of the part, but maybe a set of midi commands can do it. Would also need a way to transition back upon ending the recording of the part.

[chrisg]

Hi Quad. No, the problem exists if the global Stop Song setting to “end of loop” or "end of “measure”. In either case, if the CC-43 with Value=0 (Stop Song) is sent a bit later than 1 sec. after the “Start Song”, then it works as expected.

[chrisg]

Therefore, I may need to revert to an older Aeros software version where this problem did not exist.

Again, a workaround or a better way to send a “Play loop once” midi instruction would be great.

[steveandrewsad]

Hi, Brennan. Great job on 5.0. One suggestion/request for future versions would be to add a gesture, such as a long button hold to return to the number 1 song part. If one records a lot of tracks in a part, it can get unwieldy quickly to navigate around the parts. Might have to get the Maestro. I wish there was a Gold edition of it with silent buttons.

[DavidPackouz]

Download links for Aeros 5.0 Manual PDFs:

Aeros Manual
Printer Friendly Aeros Manual (less dark colors for less ink use)

These links have also been posted in the original post

[Chet_Gardiner]

Maybe it’s just me, hmm?

“Upgraded” Aeros to 5.0.3. Made sure all of my songs were on the card.

Two issues so far:

1. When I stomp the songs knob on the Midi Maestro I get the master folder on the Aeros and had to finger the Card icon and then finger the “songs” folder icon before getting to my songs. I hope that doesn’t mean that the songs button on the Midi Maestro is unusable or needs reprogramming.

2. The first song I tried, it played first 8 bars and then SILENCE for the rest of the song even though it showed complete waveforms.

Then I quit for now. Bigger problems in my cosmos.

[tERRY_mARTIN]

Haven’t a gig till later in the month so upgrade Aeros to the new version. Maestro takes me to songs but my scroll up and down buttons no longer work. [Sorted: the channel had changed!] But now I can’t read the song titles without bending down. Is there a way to make text bigger?

[boomski]

How can I silently erase the current recordings when the Aeros is stopped ?

[NYHC]

With the handsfree (need the last version 5.0.3)

[boomski]

*I have 5.03. installed …… how do I use it to do what I asked ? Thanks

[NYHC]

Aeros settings Handfree icon set to ON when stopped
You can select and reorganize what you want later
go back to the loop screen
Hold down the bottom left switch
A menu go open and use the schroll wheel
Select with the right bottom switch